mad00056cem mn101c93k type mn101c93k MN101CF93K internal rom type mask rom, flash mask rom rom (byte) 224k ram (byte) 6k package (lead-free) lqfp100-p-1414 minimum instruction execution time 0.125 s (at 3.0 v to 3.6 v, 8 mhz) 62.5 s (at 3.0 v to 3.6 v, 32 khz), 0.167 s (at 3.0 v to 3.6 v, 6 mhz) 62.5 s (at 3.0 v to 3.6 v, 32 khz) 0.125 s (at 3.0 v to 3.6 v, 8 mhz) 62.5 s (at 3.0 v to 3.6 v, 32 khz) ? interrupts reset, watchdog, external 0 to 5, external 6 (key interrupt dedicated), timer 0 to 3 , timer 6 , timer 7 (2 systems), timer 8 (2 systems), time base, serial 0 (2 systems), serial 1 (2 systems), serial 3 , a/d conversion ? nish, automatic transfer ? nish, usb interrupts ? timer counter timer counter 0 : 8-bit 1 (square-wave/ 8-bit pwm output, event count, generation of remote control carrier , simple pulse width measurement, added pluse (2-bit) system pwm output) (square-wave/pwm output to large current terminal pc 3 possible) clock source ................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source ........... coincidence with compare register 0 timer counter 1 : 8-bit 1 (square-wave output, event count, serial transfer clock output, synchronous output event) clock source ................ 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source ........... coincidence with compare register 1 timer counter 0, 1 can be cascade-connected. timer counter 2 : 8-bit 1 (square-wave output, added pluse ( 2-bit) system pwm output, pwm output, serial transfer clock output, event count, synchronous output event, simple pulse width measurement) (square-wave/pwm output to large current terminal pc 5 possible) clock source ................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source ........... coincidence with compare register 2 timer counter 3 : 8-bit 1 (square-wave output, event count, generation of remote control carrier , serial transfer clock) clock source ................ 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source ........... coincidence with compare register 3 timer counter 2, 3 can be cascade-connected. timer counter 6 : 8-bit freerun timer clock source ................ 1/1 of system clock frequency; 1/1, 1/128, 1/8192 of osc oscillation clock frequency; 1/1, 1/128, 1/8192 of xi oscillation clock frequency interrupt source ........... coincidence with compare register 6 timer counter 7 : 16-bit 1 (square-wave output, 16-bit pwm output (cycle / duty continuous variable), event count, synchronous output event, pulse width measurement, input capture, real time output control, high performance igbt output (cycle/duty can be changed constantly)) (square-wave/pwm output to large current terminal pc 4 possible) clock source ................ 1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of osc oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency interrupt source ........... coincidence with compare register 7 (2 lines), input capture register
mad00056cem mn101c93k timer counter 8 : 16 bit 1 (square-wave/ 16-bit pwm output [duty continuous variable], event count, pulse width measurement, input capture) (square-wave/pwm output to large current terminal pc 6 possible) clock source ................ 1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of osc oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency interrupt source ........... coincidence with compare register 8 (2 lines), input capture register timer counters 7, 8 can be cascade-connected. (square-wave output, pwm is possible as a 32 -bit timer.) time base timer (one-minute count setting) clock source ................ 1/1 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency interrupt source ........... 1/128, 1/256, 1/512, 1/1024, 1/4096, 1/8192, 1/16384, 1/32768 of clock source frequency watchdog timer interrupt source ........... 1/65536, 1/262144, 1/1048576 of system clock frequency ? serial interface serial 0 : synchronous type/uart (full-duplex) 1 clock source ................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 1 or 2; 1/2, 1/4, 1/16, 1/64 of osc oscillation clock frequency, external clock serial 1 : synchronous type/uart (full-duplex) 1 clock source ................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 1 or 2; 1/2, 1/4, 1/16, 1/64 of osc oscillation clock frequency, external clock serial 3 : synchronous type/single-master i2c 1 clock source ................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 2 or 3; 1/2, 1/4, 1/16, 1/32 of osc oscillation clock frequency, external clock ? dma controller max. transfer cycles : 255 starting factor : external request, various types of interrupt, software transfer mode : 1 -byte transfer, word transfer, burst transfer ? usb functions conforms to usb 1.1. usb transceiver built-in full-speed (12 mbps) supported. 5 end points (fifo built-in independently) fifo size (ep0, 1, 2, 3, 4) : 16, 128, 128, 64, 64 bytes ?ep0 control transfer in/out (two ways) ?ep1 to ep4 interrupt/bulk/isochronous transfer supported. settable to in or out. double buffering function supported. when the maxp size is set to a half or less of the maxfifo size for each ep, the double buffering function is made valid automatically. ? i/o pins i/o 84 common use , speci? ed pull-up resistor available, input/output selectable (bit unit) ? a/d converter 10-bit 12 -ch. (with s/h)
mad00056cem ? display control function lcd 47 segments 4 commons (static, 1/2, 1/3, or 1/4 duty) lcd power supply separated from vdd (usable if vdd = vlcd 3.6 v) lcd power shunt resistance contained ? special ports usb ports (d+, dC), buzzer output, remote control carrier signal output, high-current drive port, clock output ? rom correction correcting address designation : up to 7 addresses possible ? development tools in-circuit emulator px-ice 101c/d+px-prb101c93-lqfp100-p-1414-m (under development) ? pin assignment irq2, p22 irq1, p21 irq0, p20 tm8io, p15 tm7io, p14 tm3io, p13 tm2io, p12 tm1io, p1 1 rmout , tm0io, p10 rxd1, sbi1, an1 1, pb7 txd1, sbo1, an10, pb6 sbt1, an9, pb5 rxd0a, sbi0a, an8, pb4 txd0a, sbo0a, an7, pb3 sbt0a, an6, pb2 vss d- d+ vdd an5, pa 5 an4, pa 4 an3, pa 3 an2, pa 2 an1, pa 1 an0, pa 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 com0, p90 com1, p91 com2, p92 com3, p93 vlc3, p94 vlc2 vlc1 n.c. rxd0b, sbi0b, led0, pc0 txd0b, sbo0b, led1, pc1 sbt0b, led2, pc2 tm0o, led3, pc3 tm7o, led4, pc4 tm2o, led5, pc5 tm8o, led6, pc6 vss osc1 osc2 vdd xi xo mmod nrst , p27 dmod vref+ p56, seg25, a6 p55, seg26, a5 p54, seg27, a4 p53, seg28, a3 p52, seg29, a2 p51, seg30, a1 p50, seg31, a0 p47, seg32, d7, key7, sdo7 p46, seg33, d6, key6, sdo6 p45, seg34, d5, key5, sdo5 p44, seg35, d4, key4, sdo4 p43, seg36, d3, key3, sdo3 p42, seg37, d2, key2, sdo2 p41, seg38, d1, key1, sdo1 p40, seg39, d0, key0, sdo0 p06, seg40, nre p05, seg41, nw e p04, seg42, ncs, sbi3 p03, seg43, ndk, sbo3, sda3 p02, seg44, sysclk, sbt3, scl3 p01, seg45, nbuzzer p00, seg46, buzzer p25, irq5 p24, irq4 p23, irq3 p57, seg24, a7 p60, seg23, a8 p61, seg22, a9 p62, seg21, a10 p63, seg20, a1 1 p64, seg19, a12 p65, seg18, a13 p66, seg17, a14 p67, seg16, a15 p70, seg15, a16 p71, seg14, a17 p72, seg13 p73, seg12 p74, seg1 1 p75, seg10 p76, seg9 p77, seg8 p80, seg7 p81, seg6 p82, seg5 p83, seg4 p84, seg3 p85, seg2 p86, seg1 p87, seg0 mn101c93k lqfp100-p-1414
request for your special attention and precautions in using the technical information and semiconductors described in this book (1) if any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) the technical information described in this book is intended only to show the main characteristics and application circuit examples of the products, and no license is granted under any intellectual property right or other right owned by our company or any other company. therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) the products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). consult our sales staff in advance for information on the following applications: ? special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod- ucts may directly jeopardize life or harm the human body. ? any applications other than the standard applications intended. (4) the products and product specifications described in this book are subject to change without notice for modification and/or im- provement. at the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date product standards in advance to make sure that the latest specifications satisfy your requirements. (5) when designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. otherwise, we will not be liable for any defect which may arise later in your equipment. even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (esd, eos, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. when using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) this book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of matsushita electric industrial co., ltd. industrial co., ltd.
|
